Our Services
Duct & Vent CleaningFrom $29.99/vent
›
AC MaintenancePackages from $99
›
Indoor Air QualityThermostats, UV Lights & More
›
Quick Links
Need an Ecobee thermostat installed in Miami? We install, repair, and program all Ecobee models — the Premium, Enhanced, and Lite — plus SmartSensors for multi-room comfort. Every installation is done by a licensed HVAC technician who handles PEK adapters, C-wire issues, and proper multi-stage wiring.
We supply and install all current Ecobee models. Prices shown are for the thermostat unit — installation is additional.
Every Ecobee installation includes everything for a complete, working smart thermostat setup.
We safely disconnect your existing thermostat, label all wires, and remove the old mounting plate and unit.
Licensed tech connects each wire correctly — including Rc, Rh, Y1, Y2, G, W1, W2, C, and O/B for heat pumps and multi-stage systems.
If your home lacks a C-wire, we install Ecobee’s Power Extender Kit at your air handler — or run a dedicated C-wire for maximum reliability.
We pair and position SmartSensors in key rooms, configure the “Follow Me” feature, and set occupancy-based schedules for even temperatures.
We connect to Wi-Fi and set up the Ecobee app. We also configure Alexa, Google Home, Apple HomeKit, or SmartThings integration.
We test heating, cooling, fan, and auxiliary modes to confirm the Ecobee communicates correctly with your HVAC system before we leave.
Ecobee not working right? We troubleshoot and repair every Ecobee issue. Same-day service available.
The Power Extender Kit must be installed correctly at your air handler. Incorrect PEK wiring causes intermittent power loss, sensor disconnects, and HVAC communication errors. We fix faulty PEK installations.
Sensors showing “not responding”? Could be range issues, dead CR2032 batteries, or power problems with the thermostat itself. We diagnose the root cause and restore all sensor connections.
Ecobee reading wrong temperature? We check sensor location, recalibrate the offset setting (up to +/- 10°F), and configure Follow Me to use SmartSensors for accurate readings.
Usually caused by faulty PEK installation, blown fuse, or wiring issues. We diagnose whether the problem is at the thermostat or the air handler and fix it permanently.
Ecobee not triggering your AC? Common causes: incorrect staging configuration, wrong O/B wire setting for heat pumps, or the Ecobee running only stage 1 on a 2-stage system. We configure all stages correctly.
Ecobee has a built-in compressor protection feature that delays restarts. If your system short-cycles anyway, it’s usually a wiring or power issue. We diagnose and resolve the root cause.
Upfront pricing with no hidden fees. Bring your own Ecobee or purchase from us.
We install your Ecobee with proper wiring, PEK or C-wire, SmartSensor setup, Wi-Fi, app configuration, and full system test.
Includes Ecobee Lite with complete installation, PEK or C-wire, Wi-Fi setup, app configuration, and schedule programming.
Includes Ecobee Premium with SmartSensor, full installation, PEK or C-wire, Alexa setup, air quality monitor config. Most popular.
Diagnostic and repair of existing Ecobee. Includes PEK rewiring, sensor fixes, calibration, connectivity troubleshooting, and wiring correction.
The #1 Ecobee complaint online is PEK adapter issues from DIY installs. Our licensed HVAC techs install the PEK correctly at your air handler — or run a proper C-wire if the PEK isn’t ideal for your system.
Ecobee includes a PEK for homes without a C-wire. But installing the PEK incorrectly can damage your HVAC system.
The PEK installs at your furnace or air handler, not at the thermostat. This means opening your HVAC equipment, identifying the control board terminals, and rewiring. One wrong connection can short the board — a $400+ repair.
Ecobee supports 2-stage cooling, 2-stage heating, and dual fuel systems. Each requires specific wire configurations. Getting it wrong means the Ecobee runs only stage 1 — reducing efficiency by up to 30% without you knowing.
The O/B wire tells your heat pump whether to heat or cool. Ecobee defaults to O=cool and B=heat. If your system is reversed (common with Rheem units), your AC blows hot air. Our techs verify the correct configuration.
Sensors placed in direct sunlight, near vents, or on exterior walls give false readings. Incorrect Follow Me configuration causes the Ecobee to cool the wrong rooms. We position sensors for optimal accuracy.
“Installed the PEK myself. Now my AC blows cool for 2 minutes then shuts off. The compressor is short cycling and I can hear clicking from the air handler.”— Reddit user on r/ecobee, describing a common DIY PEK problem
Real reviews from Miami homeowners who chose professional Ecobee installation.
“I tried installing an Ecobee myself and immediately got error codes. Their tech found the wiring was wrong and my old system didn’t have a C-wire. He ran the C-wire, installed the Ecobee properly, and set up the app on my phone. Worth every penny to avoid frying my AC board.”
“Had an Ecobee Premium installed with 3 SmartSensors in my 2-story Weston home. The upstairs bedrooms used to be 5 degrees hotter. Now the Ecobee prioritizes whichever room we’re in and the temperature is even everywhere. The air quality monitor is a nice bonus. Clearly experienced with Ecobee.”
“My Ecobee SmartSensors kept disconnecting. The technician found the PEK adapter was installed incorrectly by the previous installer and was causing intermittent power issues. He rewired it properly and all the sensors came back online immediately. Problem solved in 30 minutes.”
Everything you need to know about Ecobee installation, repair, and common problems in Miami.
We install and repair Ecobee thermostats across Miami-Dade and Broward County.
We service ALL of Miami-Dade & Broward County. Don't see your city? Call (305) 607-3244
Get a free estimate in under 60 seconds. Same-day installation available. All Ecobee models and SmartSensors in stock.
